Product Description

Design:

Evaporative (FRP) Cooling towers are of vertical induced draft counter flow design with uniform water distribution and optimal heat transfer. Towers can be installed independent of wind direction.

 

Casing:

The tower casing is made of tough fibreglass reinforced plastic (FRP) and has sufficient structural strength to withstand high wind velocities and vibrations. UV – stabilised resin is used along with gel coat for longer life. It is resistant to local impacts and even if slight damage occurs, local repairs can easily be done. The portion of casing housing fill and eliminator has a round cross section. The water collection sump, also of FRP, is leak proof & avoids water spillage.

 

Fill:

The fill is of rigid Poly Vinyl Chloride (PVC) and is of honeycomb design with very large contact surface area. The fill splits the air and water into several streams, increasing the time of contact and heat transfer between water and air. The fill is in modules and is packed in the tower casing without any cutting for curves. The air pressure drop through the fill is negligible. The fills are available with flute height of 6mm, 12mm, and 19mm with sheet thickness of 1mm and 1.2mm.

 

SCSP Nozzles:

The performance of cooling tower greatly depends upon the water distribution over the fills. SCSP nozzles distribute water evenly through a wide spray angle without any dry pockets. They are lightweight and reduce the frequency of clogging. The Solid Cone Square Pattern (SCSP) nozzles produce a solid cone spray of water that is distributed in a square pattern onto the fills.

 

Drift Eliminator:

Reduces carry over losses of water. The eliminator is of rigid PVC (Applicable for square type cooling tower). The individual drift eliminators of S-shaped corrugated sheets are bonded with subsequent layers to create the structure. The entire area is thus divided into several fine S shaped mini zones each removing water droplets on the entire surface of the cell.

 

Axial Fan:

Specially designed energy efficient fans are of induced-draft axial type with adjustable pitch. Material chosen are non-corrosive of plastic, FRP or aluminium alloy. The high efficiency design ensures low running cost and the lowest possible noise level. Fan blade pitch is factory set and dynamically balanced.

 

Motors:

The motors are totally enclosed (IP55), flange type, 415 V, 3 ph, 50 Hz, induction weather proof with SS304 extended shaft and are specially designed for cooling tower application.

 

Corrosion Free:

The tower casing is of FRP, fill and eliminator are of PVC, and SS304 fasteners are used, thus eliminating corrosion, the biggest enemy of cooling tower. All steel components such as motor support, water distribution pipes, hardware etc., are hot dip or spray galvanized.

 

Light Weight:

The towers are compact and light weight resulting in easy delivery to site and installation. Light weight also saves on structural and masonry. Roof installation can also be done without any special reinforcements.

Technical Specifications:

Sl. No.Model VarianceMotorDia of FanIn / Out SizeOverall DimensionShipping WeightOperating Weight
LHPHP / RPM.NBLxWxH in mmkg.kg.
SCB-100.5 HP / 1440450 (PVC)2″ / 2½”815 x 815 x 160080220
SCB-150.5 HP / 1440450 (PVC)2″ / 2½”815 x 815 x 195080220
SCB-301 HP / 950750 (NL)2″ / 2½”1130 x 1130 x 2235235790
SCB-402 HP / 9501000 (AL)3″ / 3″1440 x 1440 x 2590255805
SCB-603 HP / 9501000 (AL)3″ / 3″1740 x 1740 x 28103101070
SCB-1005 HP / 9501400 (AL)5″ / 5″2130 x 2130 x 31005751675
SCB-1505 HP / 9501400 (AL)6″ / 6″2650 x 2150 x 32006902075
SCB-2007.5 HP / 7101800 (AL)8″ / 8″2650 x 2650 x 32259502200
SCB-25010 HP / 7101800 (AL)8″ / 8″3150 x 2650 x 335010752340
SCB-30012.5 HP / 6002200 (AL)8″ / 8″3150 x 3150 x 350012702605